Synolex Omega S6 OG 1500

Omega S6 OG 1500 – Open Gear Lubricant

Product Overview

Synolex Omega S6 OG 1500 is an open-gear lubricant for large gear contacts supplied by a defined application system. Open gearing works without the same enclosed oil bath used in many industrial gearboxes, so the lubricant must be delivered directly to the working area. Tooth size, speed, load and the installed spray or feed arrangement all influence the application. This product is selected as part of that complete lubrication method, with particular attention to distribution across the tooth contact.

Product Identification and Grade

Key Features and Benefits

1. Direct lubrication of exposed gearing

The lubricant is applied to the gear mesh through the installed feed system. Its purpose is to provide a working film at the tooth contact, where load and relative movement occur. Correct targeting matters because lubricant deposited outside the active contact does not perform the same task.

2. Attention to the full tooth width

Large gears need suitable distribution across the contact area. The feed system should deliver the product where the tooth engagement requires it, with inspection of the resulting pattern. This helps distinguish effective coverage from excessive accumulation in a limited part of the gear.

3. Selection around heavy-duty contact

Open-gear duty can combine substantial load with relatively slow movement. The lubrication programme must therefore address the specific tooth geometry and contact requirement. Synolex Omega S6 OG 1500 is a product reference for that duty, rather than a default substitute for an enclosed-gear oil.

4. Integration with the application system

Pumps, metering devices, lines and nozzles determine how the lubricant reaches the gear. The product must be suitable for those components at the actual starting temperature. A viscosity-related product number should be interpreted using the finished-product data and the feed-system requirement.

5. Controlled replenishment of the working film

The useful feed rate is the amount needed to maintain the intended lubrication condition. It should be assessed against the gear duty and the application pattern. Increasing quantity alone does not correct blocked nozzles, poor targeting or an unsuitable distribution arrangement.

6. A clear maintenance reference

Recording the full Synolex Omega S6 OG 1500 designation supports consistent lubricant supply and adjustment of the feed system. It also provides a useful reference for inspections, consumption records and comparisons with another product used in the same open-gear installation.

Applications

Use Synolex Omega S6 OG 1500 in the open-gear duty for which its application and delivery properties are confirmed. Identify the gear dimensions, speed, load and lubrication equipment before selection. The operating plan should include the application pattern and inspection method. Special run-in procedures, where required, should follow the gear manufacturer instructions.

• Large open gears with an appropriate lubricant feed system.
• Industrial gear meshes requiring direct application to the tooth contact.
• Spray or metered systems confirmed suitable for the finished product.
• Planned replacement in open gearing after an agreed changeover procedure.

Viscosity and Grade Selection

The number 1500 is retained as the product viscosity identifier for this open-gear lubricant. It is not presented here as a verified standard ISO viscosity grade or a certified measured value. Confirm the numerical viscosity, test temperature and reporting units from the finished-product specification before comparing it with another lubricant. The application system also needs to handle the product under the actual starting and working conditions. Pumpability through a line or nozzle cannot be established from the product number alone. Keep the gear-contact requirement and the delivery-system requirement together when reviewing this grade. A valid comparison should use properties measured on the same basis, while maintaining the separate assessment of open-gear performance and equipment acceptance.

Performance in the Application

The appearance of lubricant on an open gear should be interpreted together with the contact pattern and the operating duty. Coverage outside the active mesh does not necessarily demonstrate adequate lubrication where the teeth carry load. Equally, high visible consumption may indicate an application issue rather than an unusually demanding gear. Review the working contact, feed timing and distribution under the approved inspection procedure. The product designation in this range includes a viscosity-related target; it should not be converted into an assumed standard ISO grade without the supporting product specification.

Handling and Service

Inspect nozzles and feed lines using the equipment safe-service procedure. Confirm that the product reaches the intended contact area and that metering remains consistent. Record consumption against operating hours and duty. Review changes in tooth condition or application pattern with the maintenance team. Keep transfer equipment clean and avoid uncontrolled mixing during product changes.

Store the product in its original labelled container in a clean, covered area. Close the container after dispensing and use dedicated, clean transfer equipment. Protect the product from water and debris and keep batch identification legible. Follow the safety data sheet for handling and spill management, and manage used product through the applicable collection arrangements.

Why Choose This Product?

Choose Synolex Omega S6 OG 1500 for a compatible open-gear installation that needs direct lubricant delivery to large loaded contacts. The product is assessed with the feed system and tooth-contact requirement together. This gives the lubrication programme a clear focus on useful coverage of the working mesh and controlled replenishment during operation.

Product Selection and Ordering

For product selection or an order, provide the complete Synolex designation, the equipment or process application and the quantity required. Where a replacement is being considered, include the current lubricant name and the relevant equipment requirement. This allows the proposed product to be compared on application and documented properties. The current technical data sheet governs numerical specifications and any formal approvals. The comparison section below retains the product references and their qualifications, so that a potential alternative can be reviewed in its proper technical context.

The value of a product match is that it connects the lubricant to a defined job. Start with the working component or process, identify the required grade, and then compare the additional properties that affect that duty. This keeps the choice understandable for the operator who uses the product and the purchasing team that orders it. Where the equipment changes or the operating conditions are revised, update the product selection accordingly. A consistent product reference helps maintain that connection throughout the service or production cycle.

Similar Products (Equivalent Matching)

The entries below support technical comparison. A documented comparator does not establish an automatically approved replacement. Conditional alternatives require the stated differences to be resolved. A family-level lead does not verify the exact grade, and the absence of a verified entry does not mean that no product exists in the market.